|
|
|
#1
02-23-2006, 12:40 AM
|
||||
|
||||
does ur steering have a lot of play? look in here to fix that....Tutorial
WUT U NEED:
1-pen 2-screw driver 3-lug nut wrench 4-car 5-something that u can cut with 6.sand paper(i use a low coarse,and a fine wet sand) 7.ice cube 8.napkin or paper towel 9.electric motor(extra xmod motor0 10.pinion puller(if pinion is off already u dont need one) 11.9-volt battery or some power source than can be used to power elctirc motor   Before u do anything read elment6968's tut first it will show u wut you'll need to know to do mine almost all of the credit for this tut goes to element6968 on infernal xmods, the other credit goes to me for comin up with a different way of doing it... the link to his tut is http://s6.invisionfree.com/Infernal_...showtopic=6512 ...the only part i didnt like was when u had to start shaving the inside of the cup handle. MY WAY: this is were i came up with the idea of sanding down the ink tube... at first i sanded it by hand but it took way to long.. so then i saw a extra motor siting on my desk with no pinion on it.. so i picked it up saw that the ink tube fit perfectly on the output shaft of the motor..  then i took a spare 9-volt battery and hooked it up to the motor with the piece of inktube on it...  then i turned on the motor and started to push the sandpaper against the inktube while the motor was spinning. .i quicky noticed that the plastic inktube was gettin really hot and it wasnt gettin smooth it was gettin small spots of plastic bumps on it.. .so then i got another idea, OFF TO THE FREEZER, i got an ice cube and put it on a paper towel, i put the output shaft with the inktube on it on the piece of ice an i turned on the motor again and pushed the sandpaper against it again,  you dont have to always keep it on the ice the ice is just there so it dosent get to hot to where it starts to melt.this is were ur gunna need to test fit it a lot,     once you've sanded it down far enough so that it fits and it has to be tight but loose enough so that the isnt any binding or if it is hard to move when u test fit it,   reassemble and start on the other one... this is my first time doing something like this so sry if its not to clear or if i did something wrong sry if the pics are really big i dont know how to resize them right now but ill find out in an hour, cause im a lil busy right now
__________________
Look look, they hearts racin'...They start chasin'...But I'm so fast when I blow past...That they can't BREATHE ,',',',',',',CrUnK RiDaZ....http://www.freewebs.com/crunkridaz',',',',',',', Last edited by pittbull988; 02-24-2006 at 12:41 AM.. |
|
#3
02-23-2006, 09:55 PM
|
||||
|
||||
ok i take some right now
__________________
Look look, they hearts racin'...They start chasin'...But I'm so fast when I blow past...That they can't BREATHE ,',',',',',',CrUnK RiDaZ....http://www.freewebs.com/crunkridaz',',',',',',', |
|
#4
02-23-2006, 09:55 PM
|
||||
|
||||
|
not bad.
 |
|
#5
02-23-2006, 10:19 PM
|
||||
|
||||
|
ok i just finished taking the pics now..umm there probaly not gunna be the best ones cause on of my lamps broke and my cam isnt the best.. now i just have to figure out how to post pics... they might be a little big
__________________
Look look, they hearts racin'...They start chasin'...But I'm so fast when I blow past...That they can't BREATHE ,',',',',',',CrUnK RiDaZ....http://www.freewebs.com/crunkridaz',',',',',',', Last edited by pittbull988; 02-23-2006 at 10:28 PM.. |
|
#6
02-23-2006, 11:18 PM
|
||||
|
||||
|
Man thats a good tut!!
And this works awsome!!
__________________
-EVO 2005 Mustang locked rear diff stage 2 motor and springs 2300 mAh's power Body lowered over chassis -Custom 04 wide body mustang-Work In Progress http://excoboard.com/exco/index.php?boardid=15437 C-A-N-A-D-I-A-N-R-A-C-E-R |
|
#7
02-23-2006, 11:30 PM
|
||||
|
||||
|
thanks rodsrus...im glad that i found this so i could share it with u guys here....comments good or bad are welcome...wutabout that sticky gear? is this good enough for one???
__________________
Look look, they hearts racin'...They start chasin'...But I'm so fast when I blow past...That they can't BREATHE ,',',',',',',CrUnK RiDaZ....http://www.freewebs.com/crunkridaz',',',',',',', Last edited by pittbull988; 02-23-2006 at 11:34 PM.. |
|
#8
02-24-2006, 02:40 AM
|
||||
|
||||
|
although this is a great tutorial, i thought i throw the
way i did it too.... Using heatshrink tubing over the steering bar fits snug on the knuckle and allows for a tighter steering car.  |
|
#9
02-24-2006, 11:10 AM
|
||||
|
||||
|
yea i would of done that to but i didnt have any laying around
__________________
Look look, they hearts racin'...They start chasin'...But I'm so fast when I blow past...That they can't BREATHE ,',',',',',',CrUnK RiDaZ....http://www.freewebs.com/crunkridaz',',',',',',', |
|
#11
08-26-2006, 04:39 PM
|
|||
|
|||
|
try not too bring up post over 90 days old please.
__________________
BRING BACK THE CRUNK http://www.crunkridazracing.co.nr/ HTP http://htp.s2.bizhat.com/index.php?mforum=htp |
| Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
|
|
Linear Mode
