need to install nelly evo on a ma010 pcb

[acerpower]

Does anyone know how to wire a nelly evo to a ma010 pcb?
I know it must be different than installation on a evo pcb but I have seen it done on someones ma010 before.

Just wondering if anyone has done it, if they could post a pic of there pcb.
I just smoked the stock fets and would rather use my nelly evo than install a 2x2 stack.
I could really use some help here.

[Donziikid]

I have one installed on my MA010, but the earliest I could get you pictures is Sunday night. If no one has any by then I'll get them for you.

Cheers,
Kyle

[acerpower]

Thanks!
I'm not in the biggest rush to get it done,
I still have other toys to play with until then.

[TheB1GDude]

I'm sure there is a install guide somewhere but I can't find it, best I could do was a spider

http://www.xmodsource.com/forum/faq....#faq_othspider

[acerpower]

Originally Posted by TheB1GDude

I'm sure there is a install guide somewhere but I can't find it, best I could do was a spider

http://www.xmodsource.com/forum/faq....#faq_othspider

I checked the nelly instructions for the evo and compared them with the spider instructions for the evo, and although both units have the same colored wires the colors have different channel designations.
The fet pads had different colored wires going to them when I compared instructions.

Thanks for trying though, I was hoping it would be that easy.

[texan_idiot25]

http://www.woahnelly.com/images/Woah...ationGuide.pdf

http://www.woahnelly.com/indexmain.htm

[acerpower]

Originally Posted by texan_idiot25

http://www.woahnelly.com/images/Woah...ationGuide.pdf

http://www.woahnelly.com/indexmain.htm

Unfortunately it only shows directions how to install the "nelly evo" on the xmod evo. I want to install my nelly evo on a MA010 pcb and the fet pads have completely different channel designations than the evo pcb.

Thanks for trying though.

[texan_idiot25]

Maybe if you'd actually read the link, it covers Mini-Zs.

The Woah Nelly Turbo is compatible with the following 1/2x scale RC models:
• Kyosho Mini-Z, all models.
• iWaver, 1st & 2nd Gen
• RadioShack XMODS

Remove stock MOSFETS: Here’s the locations of the mosfets:
Kyosho Mini-z (all models). The MOSFETS are located on the underside of the PCB. See the picture below, they are outlined in yellow. Not sure about the F1 chassis, I think the MOSFETS are located on the top side, it is the same PCB nonetheless.

etc etc. The info is old but you asked for Mini Z instructions and here they are- straight from Ausmicro.

[acerpower]

Originally Posted by texan_idiot25

Maybe if you'd actually read the link, it covers Mini-Zs.





etc etc. The info is old but you asked for Mini Z instructions and here they are- straight from Ausmicro.

No, I actually read the link.
You gave the link for the "woah nelly" which is for the miniZ too, not the nelly evo.

I need to know how to wire this one:http://www.woahnelly.com/images/Nell...ationGuide.pdf to a mini-Z MA010 pcb.
I know I saw one on Donziikid's MA010 before so I knew it could be done, I just couldn't find how.

Like I said though, I really do appreciate the effort. Thanks.

[cowboysir03]

The wire layout for the nelly evo is the same colour coding for any mini-z pcb to nelly wiring.

You should be fine with the installation instructions for mini-z board to nelly instruction.