|
|
|
#1
04-19-2006, 02:59 PM
|
||||
|
||||
How to: servo swap
This is what i tried for my xmod so i would have the best of both worlds...a evo board, and a gen1 chassis. to do this i had to put a gen1 servo on a evo main board.
first we need to know what to solder to there are 3 solder pads to solder the servo wires to each with their own number, on an evo its (14), (15) and (16) should look like this  now solder each of the gen1 servo wires to the board in this order  on the board  i actualy used longer wires and u should too, but make some sort of marker to remember what wires are which. mine looked like this  if you dont put on new servo motor wires just solder the (blue to black) and (red to white). -/+ then solder the servo motor wires (red and blue) should look like this when done.  Last edited by crunk rida; 04-19-2006 at 03:02 PM.. |
|
#2
04-19-2006, 07:49 PM
|
|||
|
|||
|
wow dude this is tight i wish i had a gen1 because i would do this LOL good job!
|
|
#3
05-13-2006, 10:07 PM
|
|||
|
|||
|
hey crunk if you have that board, do u still have to use the old ep?
|
|
#4
05-13-2006, 10:15 PM
|
||||
|
||||
|
no, the evo board is the ep. all you need is the gen1 servo and the evo EP (board)
|
|
#5
05-13-2006, 10:15 PM
|
|||
|
|||
|
ooo ok ty cause im going to do this with my RSX and was just wondering..thank you
|
|
#6
05-13-2006, 10:18 PM
|
||||
|
||||
|
ok, good luck!
|
|
#8
05-14-2006, 04:52 PM
|
||||
|
||||
|
i turned it sideways to fit heres the pics
  and used a ink tube out of a pen to mount it on the chassis |
|
#9
05-14-2006, 04:58 PM
|
|||
|
|||
|
wow crunk i did it today and it worked then it smoked...LOL so I dont know what happened...
|
|
#10
05-14-2006, 05:05 PM
|
||||
|
||||
|
O.O did you wire it right? and where did it smoke from? make sure nothing is touching anything it shouldnt.
|
|
#11
05-14-2006, 07:03 PM
|
|||
|
|||
|
It started to smoke around the servo conncetions. But It worked before when i just had turned it on. then it started to smoke..
|
|
#13
05-14-2006, 08:19 PM
|
|||
|
|||
|
easier to change something on EVO board.
|
|
#14
05-14-2006, 11:09 PM
|
||||
|
||||
|
the reason i switched them is because the evo board can handle more current and amp flow. if it was smoking just re-wire it and make sure the -/+ and the three wires are all on right i have no idea what went wrong with yours but keep trying to fix it.
|
|
#15
05-14-2006, 11:18 PM
|
|||
|
|||
|
yea i am im going to start over form scrach and resolder all the wires on. I think this is a GREAT idea BTW.
|
|
#16
05-16-2006, 07:43 PM
|
|||
|
|||
|
sorry man but in my eyes it looks kinda pointless. did u see any real difference in preformance??
__________________
SUCK SQUISH BANG BLOW if dose' wheel wells 2" higher id be put'n 35" on dem |
|
#17
05-16-2006, 07:54 PM
|
||||
|
||||
|
yeah the liths didnt fry it cuz i had some bad cells. and i raced it agaist some 1 on a bike, the xmod won. and the board is right there if you need to solder something or change something
|
|
#18
05-17-2006, 03:34 PM
|
||||
|
||||
|
Quote:
u can put better motors without having to worry about fets and frying..and it should turn better..i think
__________________
Look look, they hearts racin'...They start chasin'...But I'm so fast when I blow past...That they can't BREATHE ,',',',',',',CrUnK RiDaZ....http://www.freewebs.com/crunkridaz',',',',',',', |
|
#19
05-17-2006, 04:09 PM
|
||||
|
||||
|
yes u dont have to put on tight turns ether its just like a evo but with a gen1 chassis
|
|
#20
05-17-2006, 10:19 PM
|
||||
|
||||
|
Quote:
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
