Go Back   XmodSource.com > Miscellaneous > Miscellaneous RC's > General 1/10 scale
Register FAQ Members List Calendar Gallery iTrader Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #81  
Old 10-16-2011, 11:00 AM
Dr. Kustom Dr. Kustom is offline
aka xmod4life
 
Join Date: Aug 2007
Location: New York
Posts: 1,083
Trader Rating: (9)
Send a message via AIM to Dr. Kustom Send a message via MSN to Dr. Kustom
Default

So I guess low clearance knuckles?
__________________
Reply With Quote
  #82  
Old 01-26-2012, 10:34 PM
mycrors4's Avatar
mycrors4 mycrors4 is offline
retired xmodder
 
Join Date: Jun 2009
Location: Los Angeles, California, USA
Posts: 1,177
Trader Rating: (4)
Send a message via AIM to mycrors4
Default

Quote:
Originally Posted by Dr. Kustom View Post
So I guess low clearance knuckles?
you can put it that way
and for today's update... a step-by-step iguide to installing the axial spur gear cover
i didn't need the part.. but i had $9 ebay bucks laying around.. and i had nothing to spend it on
i installed it with no instructions, just trial and error
took pix for about every single step.. took about 110 in total.. and im only using 27 of em aaaaaaaaannnnndddddddddd lets start



step 1: remove your transmission from the scx10(or ax10)


step 2: remove the spring+washer+nut from the slipper assembly, which control the slipper clutch


step 3: (this is a step that is NOT needed, but i did it on accident) remove the spur gear


step 4: remove the slipper assembly



step 5: unscrew the 3 screws shown ONLY to the point where the motor mount falls off





step 6: remove the 3 spacers(mine are plastic, yours might be metal or plastic) covering the rest of the screws



step 7: remove this plastic spacer



step 8: slide the back plate of the spur gear cover on, this piece replaces the 3 spacers and the plastic spacer removed in steps 6 and 7.


step 9: install the motor mount assembly


step 10: slide the slipper assembly back on


step 11: install the spur gear (this is when i realized that you never had to remove the spur gear lol)



step 12: install the spring+washer+nut which control the slipper clutch


step 13: get 3(three) 2.6x10 flathead screws, which are provided in both the rtr versions and kit versions as extra screws


step 14: twist that allen wrench(or hex driver)


step 15: install the transmission onto your scx10(or ax10)


step 16: you're done


i have yet to test drive it, but there is a piece that was un-used


not sure where it goes, but i guess i isnt meant for anything? idk, if you know, please let me know

and, i havnt finished my previous update yet.. due to a horribly stripped set screw
__________________
Any questions about 1/18 and bigger scale r/c? I'm just one Private Message away

Check out my B/S/T Thread

Want remixes of some songs... PM me.. I has DJ programing software

Inventor of the idea of using Bob Saget to name R/C parts

٩(-̮̮̃•̃)۶
Reply With Quote
  #83  
Old 01-27-2012, 10:08 AM
winner winner is offline
Xmod Expert
 
Join Date: Apr 2009
Location: atlanta georgia
Posts: 1,175
Trader Rating: (8)
Send a message via AIM to winner
Default

The wheel hexes are stripped? Just put the hex in a vice and hammer the shaft out
__________________

XBL Gamer Tag : Roar Pants
Reply With Quote
  #84  
Old 01-27-2012, 11:19 AM
mycrors4's Avatar
mycrors4 mycrors4 is offline
retired xmodder
 
Join Date: Jun 2009
Location: Los Angeles, California, USA
Posts: 1,177
Trader Rating: (4)
Send a message via AIM to mycrors4
Default

the set screw which holds the wheel hex in place is stripped, if i drill it out, the wheel hex will pull right off.
__________________
Any questions about 1/18 and bigger scale r/c? I'm just one Private Message away

Check out my B/S/T Thread

Want remixes of some songs... PM me.. I has DJ programing software

Inventor of the idea of using Bob Saget to name R/C parts

٩(-̮̮̃•̃)۶
Reply With Quote
  #85  
Old 01-27-2012, 12:06 PM
winner winner is offline
Xmod Expert
 
Join Date: Apr 2009
Location: atlanta georgia
Posts: 1,175
Trader Rating: (8)
Send a message via AIM to winner
Default

You've been needing to get a drill bit to do that since before I had my truck...... Lol just put in a vice and tap it out......
__________________

XBL Gamer Tag : Roar Pants
Reply With Quote
  #86  
Old 01-27-2012, 03:57 PM
Dr. Kustom Dr. Kustom is offline
aka xmod4life
 
Join Date: Aug 2007
Location: New York
Posts: 1,083
Trader Rating: (9)
Send a message via AIM to Dr. Kustom Send a message via MSN to Dr. Kustom
Default

That extra piece that was left out from the transmission cover is for the dig mod.
__________________
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.