|
|
|
#1
02-08-2006, 07:02 AM
|
||||
|
||||
Motors...SPEC Sheet
I figured why not start a thread that members can
enter motor fields so that other know what kinda motors are out there? Ill start... X2 Lightspeed by: Performance Xmods Pro Edition: The X-2 series uses the highest quality neodymium magnets *Silver Wire *High Speed Winding *1mm thick "FAT" Comm *Extra large armature rotor for max torque *Spiral Armature *Neodymium Magnets *Carbon Brushes *Foam Padding To Keep Motor Safe *Super Vented ball bearing can *Pre-Broken Motor *Tribo Comm Lubed *18g Motor Plug Highly Recommended: -GPM Alloy Parts -Li-Poly 12C+ 7.4v Power Source -Full 18 Wire Upgrade -Bearings -AWD **Tribo Comm Drops Required **Heat Sink Required **External Turbo / 2x2 FET stack Required Motor's tops speed is 50 mph @ 7.4v. 
|
|
#2
02-08-2006, 07:06 AM
|
||||
|
||||
|
RT-1 Modified Motor by: Performance Xmods
FET Stock Motor On Generation 1 & Evo Xmod Ball-Bearing Can High Temperature Endbell High Performance SB Magnets EGR Motor Epoxy For Best Wind Special Torque Displacement Armature Highly Conductive Carbon Brushes Note: This motor runs very well at 4.8v - 6.0v. We also recommend an 8-9 tooth pinion. .When running this motor above 6.0v, we highly recommend purchasing comm drops to prevent possible damage.
|
|
#3
02-08-2006, 07:09 AM
|
||||
|
||||
|
Hyper Torque 180 by: Performance Xmods
Hyper Torque 180 will beat a stage II motor. Runs On Stock FETs Low Amp Consumption Naturally stays cool so you don't need a heat sink Silver Brushes To Offer Max Torque & Acceleration Requires extensive chassis modifications for EVO cars. No modification required for Gen. 1 Xmods. Note: We recommend running this motor between 4.8v-7.4v with an 8-9 tooth gear ratio. Last edited by torredo; 02-08-2006 at 07:15 AM..
|
|
#4
02-08-2006, 07:14 AM
|
||||
|
||||
|
Radioshack Stock S-1
130 can Weak armature Weak magents 26,000 RPM Radioshack Stock S-2 130 can Stronger armature Stronger magnets 30,000 RPM *Use the supplied heatsink! SB Hybrid (Spinbrush) 130 can RS S-2 armature Neo magnets RPMs: N/A *Stacked FETs not required for this motor *Best run on NIMH batteries @ 800mAh rating *Must use alloy heatsink to disperse heat! Last edited by crunk rida; 05-31-2006 at 01:59 PM..
|
|
#5
05-31-2006, 01:55 PM
|
||||
|
||||
|
Stop bringing back old topics, look at the dates, its more than 60 days old! oh and btw the spinbrush is neo-magnets, check whoanelly.com for info on the motor
__________________
CRUNK RIDAZ, WE NEVER BACK DOWN!
|
|
#6
05-31-2006, 01:58 PM
|
||||
|
||||
|
true SB is not neo torredo made a special version of it "SB super modified" or something like that but the original motor is ferrite.
|
|
#9
08-29-2006, 10:38 AM
|
||||
|
||||
|
dont bring back old topics! this is a sticky so i wont close it but noone else reply to this topic plz!
__________________
CRUNK RIDAZ, WE NEVER BACK DOWN!
|
 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
