![]() |
#1
|
||||
|
||||
![]() picked this guy up with a ton of extra electronics for cheap
gonna be a backyard basher.. if the drivetrain can handle it ![]() since the electronics i have are one of those "all in one" boards, i decided to go the ridiculously stupid route of doing everything separately and doing custom work.. oh the things i get myself into... anyways, plans for it as of now: find a cheap tiny brushed esc capable of around 10A constant and 30A-40A burst ratings preferably with a lipo cut-off the way it looks right now, i might be using an the lrp ai runner from my savage xs(if the current possible buyer goes through and buys the savage without the esc). if not, ill be picking up a cheapo $10 esc off fleabay and testing that. if that fails, i will use a micro sidewinder or a mamba 25 if i can find one cheap so far i went through the truck, cleaned it up a tiny bit. i took a dremel at it and started flattening things out and making space for the t-pro hs55 clone i had laying around motor is an atomic BB2 with a custom heat sink made by the previous owner. for a receiver, i will be using a flysky receiver paired with what will most likely be an fs-gt3b. it'll be running off a losi 250mah 2s lipo that being said.. time for pictars ![]() ![]() ![]() ![]() ![]() ![]() ![]() the dremel has attacked! ![]() i know it isnt smooth in the pictures, but it was all made smooth with 200 grit sand paper afterwards. ![]() oh noes! it's nekked! ![]() ![]() because the servo horn on the original servo doesnt fit this servo, i took a piece of antenna tube and squished it to make it a tight fit on the steering rack. this will cause premature wear, but i can live with that. ![]() ![]() now for the chassis top plate, i originally planned on fabricating a custom piece then realized the original one plays a large role in stiffening the chassis. it also has some pretty deep parts that i wouldnt be able to replicate with my dremel. ill be modifying the original plate to accommodate all the electronics first up was the servo. ![]() ![]() that's all for now i will be cutting up the plate to fit the receiver and will also be getting rid of the "fins" on the front end to make space for the esc. i will most likely have to do some fab work to make this more diverse and be able to use this on my rough streets and parking lots and some dirte i will also most likely turn it into a rally car cause i like that style better, but that's in the far future
__________________
Any questions about 1/18 and bigger scale r/c? I'm just one Private Message away Check out my B/S/T Thread Want remixes of some songs... PM me.. I has DJ programing software ![]() Inventor of the idea of using Bob Saget to name R/C parts ٩(-̮̮̃•̃)۶ Last edited by mycrors4; 07-05-2013 at 09:11 PM.. |
#2
|
||||
|
||||
![]() **DO NOT USE THE BB2 WITH A LIPO**
No really don't do it. It will melt the chassis, endbell, pinion and strip the spur within minutes. The bb2 is too small for the rally/sct. I know fom experience with my rally. I ruined the board motor drivetrain and chassis within about 5 mins of mild speed RCP TRACK driving.
__________________
Xmodding is coming back? I need someone to stack fets and redo wiring on my zmod. Pm me |
#3
|
||||
|
||||
![]() what were you geared at?
at my current gearing, i should be around 145 degrees hitting a solid 22mph(before wind resistance) even without the heatsink, i should be within safe temps for the motor now if i go with the cheap $10 esc, it might change things up a bit, cause i know that esc will run pretty hot. most rc plastics are rated to around 200 degrees before they start to slowly melt
__________________
Any questions about 1/18 and bigger scale r/c? I'm just one Private Message away Check out my B/S/T Thread Want remixes of some songs... PM me.. I has DJ programing software ![]() Inventor of the idea of using Bob Saget to name R/C parts ٩(-̮̮̃•̃)۶ |
#4
|
||||
|
||||
![]() I was using a 15t pinion. Even if you can control the temps and stuff it still puts a lot of strain on the motor and fets as its way to small for the car
__________________
Xmodding is coming back? I need someone to stack fets and redo wiring on my zmod. Pm me |
#5
|
||||
|
||||
![]() id wanna test it out before giving up completely. if i run the lrp ai-runner, im 100% sure the FETs can handle it. that motor wont be pulling any more than 20A-25A at peak power
the esc is rated for a 60A current and 80A bursts
__________________
Any questions about 1/18 and bigger scale r/c? I'm just one Private Message away Check out my B/S/T Thread Want remixes of some songs... PM me.. I has DJ programing software ![]() Inventor of the idea of using Bob Saget to name R/C parts ٩(-̮̮̃•̃)۶ |
#6
|
||||
|
||||
![]() The board will be fine. The motor itself can't handle 7.4 volts with a car that is about twice the weight of the car it was designed for(micro t)
__________________
Xmodding is coming back? I need someone to stack fets and redo wiring on my zmod. Pm me |
#7
|
||||
|
||||
![]() did some testing today. motor temps were safe after a quick 2 minute run in air. full power the entire time. motor temps were at 98 degrees.
from what ive seen, temps are over 180 after 4 minutes of driving on 2s. things might change up once it gets on the ground, but i have ordered a brushless system from hobbyking that ill throw in if the atomic motor fails. i also need to get a balance plug adapter for these lipos
__________________
Any questions about 1/18 and bigger scale r/c? I'm just one Private Message away Check out my B/S/T Thread Want remixes of some songs... PM me.. I has DJ programing software ![]() Inventor of the idea of using Bob Saget to name R/C parts ٩(-̮̮̃•̃)۶ |
#8
|
||||
|
||||
![]() Quote:
good news. nothing blew up! i soldered on 2mm bullets for the esc. and also soldered on the tiny white connectors for the battery since i had them laying around. made a deans adapter for my charger pinion came undone on the first run.. literally, the first 2 seconds LOL ill use stronger super glue next time, but it had to come off anyways for a the new motor mount but i did give it throttle and whatnot. nothing seems to be getting unusually hot yet i have ordered a new full aluminum motor mount because i stripped mine out from the bottom. should be coming in tomorrow or the day after. i will wait until then to take it apart. along with the motor mount is the adapter for the balance plug on the lipos. for now.. 1 picture will wire it up all nice and neat once everything is running the way i like ![]()
__________________
Any questions about 1/18 and bigger scale r/c? I'm just one Private Message away Check out my B/S/T Thread Want remixes of some songs... PM me.. I has DJ programing software ![]() Inventor of the idea of using Bob Saget to name R/C parts ٩(-̮̮̃•̃)۶ |
![]() |
Currently Active Users Viewing This Thread: 46 (0 members and 46 guests) | |
|
|