|
#1
|
||||
|
||||
Warning! Propulse tires may fail at high speeds.
I was doing some high speed laps around a large, smooth parking lot with the 3s lipo in my RC18t(6800kv mamba) when I had a major tire failure......................................
I got on her a little too hard and blew the back tire right out.(followed by an ugly tumble) I'm glad I only paid $1 for the set of wheels/tires. They grip well but you might have some major tread separation at extreme speeds.
__________________
Toyota, Moving Forward. Even if you push the breaks. Last edited by acerpower; 05-11-2010 at 06:27 PM.. |
#2
|
||||
|
||||
haha that is awesome.... I've ballooned mine with the brushless but nothing that bad!
__________________
Duct Tape is like the force:- it has a light side and a dark side and it binds the universe together.....
|
#3
|
||||
|
||||
I did that to mine too lol, I was running on hard asphalt. If it wasn't a V-tread it wouldn't have torn, the buggy tires hold up much better.
__________________
7mm front suspension travel from my EVO!!! see how I did it here! http://www.xmodsource.com/forum/show...342#post249342 |
#4
|
||||
|
||||
lol im confused on how that happened, on a smooth parking lot
if it wasnt very smooth, it would make much more sense.. lol just drive it like that.. see what happens lmao this is the best slogan ive seen in ages its the byt slogan(or maybe a slogan from a member from byt, anyways, still an awesome slogan) "If it still moves, it aint broken" and it fits in well with this one "Drive til it's broken" which leads to this one "Drive til it doesn't move anymore" lol
__________________
Any questions about 1/18 and bigger scale r/c? I'm just one Private Message away Check out my B/S/T Thread Want remixes of some songs... PM me.. I has DJ programing software Inventor of the idea of using Bob Saget to name R/C parts ٩(-̮̮̃•̃)۶ Last edited by mycrors4; 05-11-2010 at 08:10 PM.. |
#5
|
||||
|
||||
Quote:
__________________
Brushless RC18T, Brushless Micro DT, Midwest AeroStar .20, SCX10 Honcho, Duratrax 1/5 Firehammer MT, Traxxas Nitro 4Tec 3.3 |
#6
|
||||
|
||||
The tires were ballooning like crazy on 2s lipo so I guess this was bound to happen on 3s.
At least they held up for a few minutes. Unfortunately all the rubber tires I've tried, even 1/10 touring car tires, balloon to one degree or another. I have a bunch of different style propulse tires to run and I spent $1 a set, so that will hold me off until I decide to buy some 1/10 foam tires.
__________________
Toyota, Moving Forward. Even if you push the breaks. |
#7
|
||||
|
||||
Quote:
__________________
Brushless RC18T, Brushless Micro DT, Midwest AeroStar .20, SCX10 Honcho, Duratrax 1/5 Firehammer MT, Traxxas Nitro 4Tec 3.3 |
#8
|
||||
|
||||
Quote:
i run 1/10 onroad tires(rubber) on my rc18t with a stronger set up(8000kv mamba w/ 3s lipos) and ive never had a problem, but i will tell u, you lose control a lot easier than if u had 1/18 truck wheels, because its not as soft, but you get used to it
__________________
Any questions about 1/18 and bigger scale r/c? I'm just one Private Message away Check out my B/S/T Thread Want remixes of some songs... PM me.. I has DJ programing software Inventor of the idea of using Bob Saget to name R/C parts ٩(-̮̮̃•̃)۶ |
#9
|
||||
|
||||
if you tape the inside of them them with duct tape or gorilla tape it will help cut down on ballonong
|
#10
|
|||
|
|||
if you'd like i have a brand new set of rear foamies for a mini-t, they should fit right on rc18 or a propulse. you can have them if you cover shipping
__________________
XBL Gamer Tag : Roar Pants |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|