Thread: Pulsing Neons
View Single Post
  #1  
Old 11-10-2008, 08:05 PM
fieldfairy2's Avatar
fieldfairy2 fieldfairy2 is offline
late model, xmods, microt
 
Join Date: Oct 2007
Posts: 972
Trader Rating: (5)
Default Pulsing Neons

Yep pulsing neons, like on my "saleen makeover and track car thread".

Materials:
-Soldering Iron (i used a 15w but now i use a 40w so whatever works,30 is the best)
-Solder
-Barricade Flashing Police Lights
-Cutters(optional)
-3mm Leds(color of your choice)
-Neon/underglow
-Resistor(i used a 100ohm, but anything can be used, the higher the ohm's the slower the leds blink and the less bright the leds are)
-hot glue gun
-hot glue
-Wire (thin and very flexible, unlike the wire i used, lol, you will need 5 wires of any length, i have about 2-3inches)
-electrical tape or heat shrink
-hobby knife/xacto
-pliers
-wire strippers
-you chassis and body

Neon/underglow(very similar to the first couple of steps in Noturday's tut):

You want to grab your underglow or neons and cut the silver tape off.

Now that the tape is off grab you pliers and take the leds off from the battery cover.You can approach this different ways, cut the neons off the board, unsolder the neons from the board or like i did use the pliers.

You should have the battery cover with nothing else on it, set this aside for future use.

Modifying the Flashing police lights:


Grab you Flashing police lights form the barricade body kit. Carefully cut the Heatshrink off with the x-acto Knife

(leds are off in this picture)

Next is to remove the leds(both leds) from the Police lights.

Using the Soldering Iron and pliers you can unsolder the the leds off(both). However you approach this is fine just don't ruin the board or take off the solder points.

Strip all ends of all the wires to about 5mm

Grab one of the leds. Solder wires( i have about 2-3inches in length) on to it, on each leg or prong.(positive and negative).

Solder the wires from the led to the Electronics side(blue) to where on of the leds used to be. With the capacitor and the plug facing you, the positive is on the top and the negative is on the bottom, like so:





Now that was the easy part.

Grab you other led and solder 2 wires onto the positive prong and one wire to the negative one.



You want to solder the 2 positive wires top where the red and yellow wire come in from the plug:



With the capacitor facing you again, look at the top left corner of the Police lights. There is a black box with 3 prongs, 2 prongs closest to you, on one side, and one prong on the other side, you want to solder the negative wire on that one prong facing away from you.




You can test lights now, to make sure hey work.

If they work Use the hot glue gun the glue all the wires you soldered down to the board, it relieves stress on the joints.

Using the resistor(100ohm or size of you choice) solder it in between(splice) the black wire on the plug.



Use electrical tape or heat shrink to cover the solder joints.

With the underglow battery cover on your chassis, you can install the light kit and make sure it works. Find a mounting place for the Pulsing neons or just set them on the chassis somewhere, bend the wires(with the leds) between the wheels and connect it the battery cover, you can glue or tape the wires in place.





That is it. have fun. If there are nay mistakes please say so. I will be trying to get some more pictures for places in the tut and as for the quality of the picture i did the best i could with a 7year old camera and i new video.

the only downside is that one led blinks a little brighter than the other.

Thanks.

Fieldfairy2
__________________
Track car v2.0
fieldfairy2's mini late model
Operation black widow
H-Crawler