Hmm...

http://i1179.photobucket.com/albums/...IMGP0143-5.jpg

Update: Bed work began.

http://i1179.photobucket.com/albums/...IMGP0142-6.jpg

http://i1179.photobucket.com/albums/...IMGP0144-5.jpg

http://i1179.photobucket.com/albums/...IMGP0147-5.jpg

http://i1179.photobucket.com/albums/...IMGP0148-6.jpg

Update: Got my Holmes Hobbies Cobalt Puller 7T motor in the mail today, been waiting for this for awhile now. Here's a few comparison pics between the HH7T and the HH 540.

http://i1179.photobucket.com/albums/...IMGP0142-7.jpg

http://i1179.photobucket.com/albums/...IMGP0144-6.jpg

Because of the new motor is a bit longer than the old one, so I had to re-locate the battery to the rear of the chassis and removed the truggy bed.

http://i1179.photobucket.com/albums/...IMGP0152-5.jpg

http://i1179.photobucket.com/albums/...IMGP0146-4.jpg

http://i1179.photobucket.com/albums/...IMGP0150-6.jpg

Update: Got some more goodies in the mail recently.

48P 20T pinion gear.

http://i1179.photobucket.com/albums/...IMGP0157-2.jpg

http://i1179.photobucket.com/albums/...IMGP0162-1.jpg

Gens Ace 2S 5000mAh 7.4V Li-Po battery pack.

http://i1179.photobucket.com/albums/...IMGP0153-2.jpg

Switch out the banana plugs to deans plugs.

http://i1179.photobucket.com/albums/...IMGP0154-1.jpg

http://i1179.photobucket.com/albums/...IMGP0155-1.jpg

Update: Look what showed up today...Tekin T35 Heavy Duty motor!

http://i1179.photobucket.com/albums/...IMGP0158-2.jpg

http://i1179.photobucket.com/albums/...IMGP0171-1.jpg

By far, out of all the motors I've used on this rig, the Tekin T35 Heavy Duty is my favorite. As you can see, my SCX10 is getting dirtier each day.

http://i1179.photobucket.com/albums/...IMGP0176-1.jpg

A video of the Tekin T35 in action!

YouTube Video

Anyone else try to do parallel parking with their SCX10?

YouTube Video

I think it's time for a car wash.

http://i1179.photobucket.com/albums/...IMGP0164-1.jpg

http://i1179.photobucket.com/albums/...IMGP0166-2.jpg

http://i1179.photobucket.com/albums/...IMGP0177-2.jpg

http://i1179.photobucket.com/albums/...IMGP0169-1.jpg

After having all those fun times with the SCX10, I end up with a broken drive shaft. Looking into replacing both shafts, any recommendation?

go with the MIP shafts if you can afford em, or the junfac ones

both are really good, ive had experience with both

How about the RC4WD punisher drive shafts?

never had experience with em, but from what ive heard and seen, rc4wd internal products arnt the best

Update: Got my MIP drive shafts and RRP outdrive diff lock gear in the mail today, the steel idle gear should show up tomorrow.

http://i1179.photobucket.com/albums/...IMGP0144-7.jpg

http://i1179.photobucket.com/albums/...IMGP0145-3.jpg

Comparison of the stock plastic drive shaft with metal yoke and the MIP drive shaft.

http://i1179.photobucket.com/albums/...IMGP0147-6.jpg

Got it mounted on the SCX10.

http://i1179.photobucket.com/albums/...IMGP0149-5.jpg

http://i1179.photobucket.com/albums/...IMGP0152-6.jpg

http://i1179.photobucket.com/albums/...IMGP0154-3.jpg

Arghh...plastic servo gears...

http://i1179.photobucket.com/albums/...AG0116-1-1.jpg

Update: Time to beef up the tranny.

-Hot Racing stainless steel idler gear
-RRP one piece hardened diff locker gear

http://i1179.photobucket.com/albums/...IMGP0141-3.jpg

Time to open up the tranny.

http://i1179.photobucket.com/albums/...IMGP0147-7.jpg

Here's a comparison pic of the diff locker from the SCX10 kit and the diff locker from RRP.

http://i1179.photobucket.com/albums/...IMGP0149-6.jpg

Full metal gears tranny.

http://i1179.photobucket.com/albums/...IMGP0151-4.jpg

http://i1179.photobucket.com/albums/...IMGP0152-7.jpg

Fresh snow!

http://i1179.photobucket.com/albums/...IMGP0143-6.jpg

http://i1179.photobucket.com/albums/...IMGP0145-4.jpg

Update: Headed over to the junk yard and pick up some 2nd hand OEM steel rims, and some Prowler XS tires.

http://i1179.photobucket.com/albums/...IMAG0275-1.jpg

Your junk yard has a much finer selection than mine..

I just got lucky this time. :lol:


Update: Stock.

http://i1179.photobucket.com/albums/...IMGP0149-8.jpg

Polished.

http://i1179.photobucket.com/albums/...IMGP0148-9.jpg

Comparison pics.

http://i1179.photobucket.com/albums/...IMGP0145-6.jpg

http://i1179.photobucket.com/albums/...IMGP0146-6.jpg

Only got 2 rims done, still have 2 more that need to be polish.

http://i1179.photobucket.com/albums/...IMGP0165-3.jpg

where's the dang LIKE button? ;)...wait...wrong forum...

LOL

im lovin the polished look over the white one. gives it that "project truck" look
keep em comin jason, im always anxious every time you have an update

Did the Tekin 35T come with any wiring? I am thinking of getting one but don't want it to arrive and then realize I should have bought wire and connectors at the same time.

you just have to soldier your ESC wires to the tabs. i may be wrong but like any other brushed motor it comes with just the motor, meaning no wires

winner here is right
just solder the esc wires onto the motor

most high end brushed motors do not come with wires.